Bag Kit

When Your Smoke Bomb Kit Is A Dud, Try This.

Sometimes, learning how to make a colored smoke bomb can be tricky. Even if you think you already know how! You can still have problems getting your colored smoke to burn bright and without sputtering even if you're an old pro at making smoke bombs.

Many people get their smoke supplies from suppliers that have been offering organic powdered dye pre-mixed with the other necessary colored smoke chemicals for years. These premixed colored smoke components make it a lot faster and easier to make smoke grenades and smoke bombs. Typically you can buy a pound of the colored smoke mix, combine it with a pre-measured amount of potassium chlorate (KClO3), load it into a capped tube, insert the Visco fuse and voila! You have a homemade smoke bomb, ready to light and enjoy. Usually.

Occasionally I would have problems getting the colored smoke to light. When this problem became repetitious, I decided to roll up my sleeves and look into it. What I found was anything but earth shattering, but a good lesson in simple pyrotechnic detective work and it is exactly the same kind of problem diagnosis and solution process which anyone who makes fireworks will eventually run into.

Ease and simplicity is the reason to buy a colored smoke bomb kit. But suppliers perhaps have made it too simple, they may overlook the obvious. I was mixing the two-part colored smoke components (smoke mix and KClO3) correctly, according to the instructions my supplier provided but when I tried to light the newly assembled smoke bomb it wouldn't burn or it would light and then sputter and fizz out.

Ideally when you light the smoke grenade it is supposed to smolder, not catch on fire. The key is having exactly the right ratio of the potassium chlorate oxidizer to smoke mix fuel. Imprecise measurements can lead to the mix burning too fast, resulting in disapointing smoke colors. Err in the other direction and your colored smoke mix will not ignite at all. Accurate measurements are critical.

I took my kit and my problem to my supplier and jumped right in. They took samples from the batch of smoke mix that my kit had come from, identified by lot number, mixed it properly with the KClO3, and touched it off outside the office. They too, had some kind of a problem. Initial thought was that perhaps the lab which formulates their colored smoke mixes in large quantities, had changed the composition in some way. We called them up and they said nothing was different, but chemicals can vary from batch to batch and unless you do time consuming and expensive testing of each new batch you may never know.

If we increased the amount of KClo3 added to the mix, we could sometimes get it to burn, the problem persisted. Then an idea pulled from the sky; one or both of the two-part smoke mixture must have gotten clumpy which happens when a powdered chemical gets a little bit of moisture in it thereby increasing the particle size. Upon close observation you could see that the KClO3 had indeed developed clumps. We sifted some of the blue smoke mix through a 30-mesh kitchen strainer and found the same thing. Theory confirmed! We discovered that humidity was affecting the powdered chemical compostion of the kit contents and altering the burn rate.

When particle sizes are larger surface area is decreased. The burn required depends on the tiny fuel and oxidizer particles being in close contact with each other. We were confident we had the mix proportions exactly right as long as the particle size was fine and free flowing. With the clumps in the two powders, due to humidity, he interactive surface area was reduced and was no longer adequate for the recipe we were using. That's why adding a little more potassium chlorate had solved the problem for some of the tests, the decreased surface area meant that if we changed the ratio of oxidizer to smoke fuel we could indeed get the smoke mix to light. There had to be a revision in the method of mixing and milling the chemicals and confirm the smoke fuel to KClO3 ratio.

Armed with the knowledge that it was indeed and merely a particle size issue, we set out to resolve the problem in a way that would involve the least hassle and expense, good ole trial and error. We worked with very small batches as to speed up the process by reducing weighing, milling, and mixing. It also reduces the cost of materials which may be wasted during the testing.

I don't do this indoors any more as smoke dyes are easily blown around by even stray puffs of wind so my first problem was finding someplace that wasn't windy. I found a protected corner against a shed, out of the wind, and set up my scale, two coffee grinders, some mixing cups, a small kitchen strainer screen, and my trusty pyro notebook. 14 was the target ratio.2 grams of smoke mix to 5.2 grams of potassium chlorate. That's the ratio we devised early on that would work with all of our smoke mixes, regardless of color. And we knew from history it would work. My test burn container for the following experiments was a 9/16" ID x 1-1/2" long tube (called an M80 tube in some circles) with a cardboard plug in one end, the other end open. (side note; colored smokes do not have to be confined to burn).

• Experiment 1: I added the two chemicals together in a plastic zipper bag and kneaded them together for ten minutes. With a test tube filled, we installed the Visco fuse and lit it. Would not burn. This mix would not even light when exposed to an open flame of a blowtorch.
• Experiment 2: I repeated the process in Experiment 1, but with an additional 10% potassium chlorate. Fuse was lit but it, too, failed to ignite. Blowtorching the loose mix caused it to light, but it could not sustain the burn, and went out.
• Experiment 3: Repeated #2, again added 10% chlorate, instead of bag mixing, screened the mix 3 times. Lit the fuse, and the smoke mix ignited, the burn was sustained, but with a "sputtering" burn, and an okay, but not rich blue smoke.
• Experiment 4: Since the potassium chlorate was the lumpier of the two components, I used a coffee and spice grinder to grind the chlorate to a fine, fluffy powder, with about 20 seconds of pulse milling. Weighed the two components in the original 14.2/5.2 grams ratio. Screened the two components together 3 times. The mix burned correctly.
• Experiment 5: Repeated #4, but I also blade milled the smoke mix for 20-30 seconds as well, before screen mixing together 3 times. The mix burned with greater results. Perfect, rich, blue smoke. The volume of smoke was the greatest of all the test burns.

The particle sizes of both components need to be as small as possible. If there is a problem getting the smoke mix to burn, then milling both components separately to a finer particle size, as well as using a better mixing method will likely solve the problem.

This isn't an A-Z solution to fireworks problems. But if you think particle size or clumping may be your problem, the method described above is a quick and simple test to find out.

Making colored smoke bombs is easy, fun, and satisfying when you get the results you expect. Many thanks to the gang at Skylighter, Inc. for putting in the long hours to make my smoke bomb kit deliver the smoke I demand.

can anyone help me i'm tring to install an air bag kit on my 1970 chevy c 10 please help?

Since it looks like everyone misunderstood what you were asking, let me try to help out. Air Ride Technologies makes a front and rear kit for 63-72 GM pickups. Their rear kit is extremely simple and even uses the stock shock mounts. Speedway Motors has fairly resonable prices on Air Ride kits. See link below. Everything you need is on one page.

Alex Yarn Craft Kit in Carry Basket (Zimbio)

### Alex Yarn Craft Kit in Carry Basket

**alex toys my art - click on the image below for more information.**

* Kit includes 6 balls of brightly colored yarn, wooden knitting needles,
plastic crochet hook, plastic needle and easy to follow instructions

* Perfect travel activity

* Stylish wicker basket holds all of your supplies

* Illustrated instructions makes knitting easy to learn

* Won Oppenheim Toy Portfolio's "Gold Seal" Award

## alex toys my art

Learn to knit and crochet a chic scarf and bag. Decorate with fashionable
flowers and tassels to dress up your creations. This charming wicker basket
contains everything a beginner needs to learn the simple stitches in these
easy projects. Kit includes six brightly colored skeins of yarn (50 yards
each), wooden knitting needles, plastic crochet hook and easy-to-follow
instructions with line drawings to clearly illustrate the step-by-step
directions.

### Alex Yarn Craft Kit in Carry Basket

Click on the button for more alex toys my art information and reviews.

**Clockwork Family**

_Image by birdtrouble_

**Add your own answer in the comments!**

**_Question by density_: My best friend is rude to me and nobody else...?**

the ...

Zimbio

Airsoft GI - Emergency Go Bag Kit with OE TECH Urban Go Bag Multicam